Measure mowing area, not property size
Published by Fordham Tucker · Manufacturer sources checked November 15, 2026 · No hands-on mower testing
For a robot mower, start with the grass it will actually cut. In the worked example below, a half-acre property contains just 8,000 square feet of mowing area. The remaining land still matters for routes and installation, but it is not grass coverage.
Use this guide to make a measurement sheet before comparing models. See the worked example, copy the blank worksheet or understand the capacity allowance.
Make a mowing map before choosing a model
- Draw each patch of grass separately. Label the front, back and side lawns. Mark the charging location you are considering and the routes between patches. A lot boundary or real-estate acreage is a useful outer reference, not the area to enter in the calculator.
- Measure the intended grass polygons. For a rectangle, multiply length by width. For a triangle, multiply the base by its perpendicular height and divide by two. Split irregular shapes into smaller pieces. Keep a sketch so that neighboring pieces do not overlap.
- Subtract only exclusions inside those shapes. Deduct beds, patios and other areas the robot will not mow. If your outline already follows the grass around a bed, that bed is already excluded: do not subtract it again. Record any grass you deliberately plan to maintain by hand separately.
- Walk the boundary after measuring from an image. Satellite imagery may hide a bed beneath a tree or show an older layout. Check gates, steps, narrow strips, pond edges and the actual usable route. Re-measure uncertain sections before shopping at a model's limit.
Triangle = base × perpendicular height ÷ 2
Net mowing area = measured zone shapes − exclusions inside those shapes
1 acre = 43,560 sq ft · 1 m² ≈ 10.764 sq ft
A measuring wheel, tape or map measuring tool can help collect the dimensions. None of these steps proves that a robot can safely navigate the result. Keep the area calculation and the installation check as separate tasks.
Worked example: a half-acre lot with 8,000 sq ft of grass
This is a constructed example, not a measured customer property or mower test. The property is 21,780 sq ft (0.5 acre). Its house and garage footprint occupy 2,400 sq ft, driveways and paths 1,800 sq ft, patio 580 sq ft, and planted or wooded areas 9,000 sq ft. Those non-overlapping exclusions total 13,780 sq ft, leaving 8,000 sq ft to mow.
Cross-check that result by measuring the grass zones directly:
| Zone | Measurement and exclusion | Net grass |
|---|---|---|
| Back lawn | 70 × 90 ft rectangle, less a 10 × 10 ft bed | 6,200 sq ft |
| Front lawn | 60 × 35 ft rectangle, less a triangular bed: 30 × 20 ft ÷ 2 | 1,800 sq ft |
| Total | 6,200 + 1,800 | 8,000 sq ft |
Enter 8,000 sq ft in YardFit. That is about 0.184 acre or 743 m². Do not enter the half-acre property size and then subtract the beds a second time in your notes. If the two calculation methods disagree, check overlapping shapes, excluded areas and units before choosing a mower.
Your measurement worksheet
Copy this table into your notes or print the page and fill it in by hand. Use one unit throughout. Keep your address and yard sketch on your own device; this worksheet does not submit anything to YardFit.
| Zone and dimensions | Inside exclusions | Net area and unit |
|---|---|---|
| Front: __________________ | __________________ | __________________ |
| Back: __________________ | __________________ | __________________ |
| Side / other: __________________ | __________________ | __________________ |
| Total intended mowing area | Exclude overlaps | __________________ |
Alongside each zone, note its connection to the next lawn, narrowest usable passage, slopes, preferred cutting height, hazards and available mowing hours. Mark measurements that are estimates. A smaller total is not a reason to ignore a difficult route.
Keep measured area and planning headroom separate
YardFit compares the actual grass area with each published rating, then shows a separate planning allowance. The 1.25 and 1.5 multipliers are our editable editorial assumptions, not manufacturer requirements or measured productivity. The allowance does not change how much grass you have.
| Layout assumption | Calculation | Planning target |
|---|---|---|
| Mostly open | 8,000 × 1.25 | 10,000 sq ft |
| Several zones / obstacles | 8,000 × 1.5 | 12,000 sq ft |
A 0.25-acre rating equals 10,890 sq ft. The US Navimow i210 AWD is listed at 0.25 acre. In this example, 8,000 sq ft is within that rating. It also fits the 10,000 sq ft planning target, but falls short of the 12,000 sq ft target. That second result means less allowance than you selected; it does not prove the mower cannot work and does not automatically justify buying a more expensive model.
Near a limit, ask the manufacturer to review your measured area, route and schedule. A capacity rating is not a promise that all the grass will be cut on one charge or within a short daily window. Charging, growth, travel and available working hours all need to fit the plan.
A buying worksheet is not the mower's installation map
The Navimow i2 AWD manual, section 4.1, distinguishes mowing-zone boundaries, off-limit islands and connecting channels. It also describes isolated zones that require carrying the mower to the lawn and back to charge. Record those connections on your sketch rather than assuming that adding areas makes them reachable.
Mammotion's current mapping instructions for LUBA 3, LUBA mini 2 and YUKA mini 2 distinguish manual mapping for complex layouts from automatic mapping for neat, level lawns with clear boundaries. These are installation workflows performed with the mower. Measuring the grass before purchase does not replace them.
Also distinguish recommended mowing area from maximum stored-map area. The current i2 AWD product footnote discusses map storage up to 1.2 times the recommended area, subject to layout and complexity. YardFit does not treat that storage allowance as an increase in recommended mowing capacity. Ask how exclusions and connected zones count for your exact model and software version.
No-go zones are not a substitute for the physical boundary protections or clearances required by a model's manual. For ponds, drops, public roads, steps or sloped boundaries, obtain a site-specific installation review. Read our gate and separate-lawn survey and slope measurement guide before treating the area result as a shortlist.
Take one consistent set of numbers to the seller
- Actual mowing area, units, zone count and which figures remain estimates.
- A sketch of connecting routes and the narrowest usable gate or passage.
- Interior slopes, boundary hazards and the cutting height you need.
- Safe daily working hours, including charging and any manual carrying.
- The exact regional model, its recommended area and how its map limit is calculated.
Ask for an answer against those facts and keep a copy. Confirm return conditions and the time available to try the mower on growing grass before ordering. We have not field-tested these models; a complete area worksheet is preparation for the installation decision.
Keep the worksheet nearby, then compare the published limits and optional headroom separately.
Check my lawn capacity →Sources and method
Manufacturer pages checked November 15, 2026: Navimow i210 AWD rating and map-storage note; Navimow i2 AWD manual, section 4.1; Mammotion first-map instructions. Geometry, worksheet and worked examples are YardFit's own explanation. Capacity multipliers are planning assumptions. Read our methodology and disclosure and privacy notice.